Skip to main content

No Service Password Recovery - It is not the end of the world

Myth


Having a chat with some people and this came up in conversation, "no service password recovery" and people seemed to be taking it quite literally. e.g. if you forget your password the devices it is dead and needs to go back to Cisco, not being a security guy I though ok, but it was bothering me. So a quick lookup on cisco http://www.cisco.com/en/US/docs/ios/12_3/12_3y/12_3ya8/gtnsvpwd.html

Fact


In fact what this feature does is prevent you from getting access to the startup configuration, you can recover the device to FACTORY DEFAULT - the config has gone. Of course will have a backup of the config so it should be no big deal to switch this feature on every device, assuming the device supports it.

 

Take Note of the comments : "

Before deploying this feature, TEST the password recovery. Some platforms (based on ROMMON version) are EXTREMELY hard to recover.

http://blog.ioshints.info/2007/12/recovering-from-disabled-password.html

"

Thanks Ivan

 

Comments

  1. Before deploying this feature, TEST the password recovery. Some platforms (based on ROMMON version) are EXTREMELY hard to recover.

    http://blog.ioshints.info/2007/12/recovering-from-disabled-password.html

    ReplyDelete
  2. Yep, we like to use this feature when deploying equipment into semi-trusted or untrusted environments. Gear residing at a vendor/partner's site, small ASAs/routers deployed to employee's homes for EasyVPN, etc. If someone wants to get clever and crack the device for fun, or it gets stolen, they will get nothing useful.

    Good post to clarify the feature!

    ReplyDelete

Post a comment

Popular posts from this blog

ASR1006 Dual Route Processors Password Recovery - Tip

I recently ran into an issue when trying to perform dual route processors password recovery on a Cisco  ASR1006
Problem
After breaking into rommon mode and using confreg to ignore the startup configuration, during the rest the ASR1006 loaded the startup configuration!!!!!!!!
Solution
So quick and simple, I pulled one of the RP and preformed password recovery running on a single RP. All went according to the Cisco documentation

http://www.cisco.com/en/US/docs/routers/asr1000/install/guide/routers/asr1_hwc.html#wp1045971



After the system running on a single RP was recovered and fully booted I waiting for 5 minutes just to be sure; then I inserted the second RP and allowed everything to sync up.



All was well again :) phew



Note: The system was previously fully functioning with dual RPs; a configuration error was made during Tacacs+ configuration which resulted in lockout.


Summary
I hit an issue recovering and ASR with dual RPs, so rather that spending hour researching, I decided very quickly to go …

Where are all the AAA and PKI solutions gone for Dot1x

More Question than answers
(This series will be based on an enterprise with >20,000 dot1x devices)

I have been looking into dot1x authentication for Wired and Wireless devices based on device identity using x.509 Certificates. While I understand PKI, AAA, PEAP and sorts I had never really had the opertunity to bring these technologies together. I quickly found out that despite this stuff being around for years,  it was difficult to answer the following questions:

Which PKI solution should I use?
Which AAA solution should I use?
How to setup the PKI solution?
Does the PKI server need to be part of AD?
What if the clients are not in AD e.g. Wireless Tablets?
How do I issue certificates for devices?
How to configure the devices (wired and wireless)?
What AAA server do I use?
How do configure the rules and policies and identify clients?


What are the answers?
I am going to kick off a series here at networking-guru.net that tries to address the question above; I have limited time but hopefully I can …

Dell Latitude D830 SSD Upgrade

Slow Laptop Syndrome
I have a LATITUDE D830 : INTEL CORE 2 DUO T7500 4GB Ram from 2008, I did get a fairly high specification at the time, so it has always had pretty decent performance. However I haven't been using it for a while and when I did it seemed slow compared to my Core 5i desktop computer. (I use Windows 7 ultimate with the latest updates)

Laptop for Work
Now I might be doing a fair bit of travelling to customer sites in the near future and the last thing I want is a poorly performing Laptop, so I decide to ditch all the crap I had on it like iTunes, movies, miscellaneous software and cut back to a basic "work" PC. After all I do have iPhone, iPad and new kindle (soon) for all my multi media needs.

I purchased a "Corsair 120GB Force 3 SSD 2.5" SATA-III 6Gb/s Read = 550MB/s, Write = 510MB/s" from ebuyer.com. Now I am guessing that SATA-II rather that SATA-III on the system board, but the price difference between SATA-II and SATA-III was nothing …